Dignity. Technology. Sustainability. — Redefining the Afterlife Industry.
Dignity. Technology. Sustainability. — Redefining the Afterlife Industry.
Funeral Home Turnkey Solution
Funeral Home Turnkey Solution
Instead of coordinating five suppliers across five functional zones, you contract one partner who owns the interfaces between them — from the first site survey to the day the facility runs as one system.
Whole facilityScope
Design–build–commissionDelivery
Five integratedZones
01 What it solves
Funeral homes are procured the way ordinary buildings are: each functional zone goes out to its own supplier. Cold storage comes from one company, cremation and flue gas from another, ash storage from a third, air safety from a fourth, information systems from a fifth.
Each supplier is competent and each delivers to its own standard. The problem appears at the boundaries: the refrigerated room's dimensions do not match the transfer equipment, the exhaust route conflicts with the ductwork, the control cabinet expects signals that no upstream device produces. By the time it surfaces it is a site problem, and the buyer is the one holding the schedule.
Inconsistent standardsIncompatible interfacesUnsynchronised constructionPoor inter-system coordination
The cost shows up four times: duplicated investment where two suppliers each solve the same interface, a construction programme that slips every time a boundary is renegotiated, operating cost from systems that never learn to coordinate, and maintenance that stays expensive because responsibility for the whole was never assigned.
02 What the solution includes
Unified planning
Functional zoning, capacity planning and site layout decided together, so the five zones are sized to one another rather than to five separate briefs.
Integrated design
Equipment interfaces, pipe and duct routes, power and control signals fixed at design stage — the point where they are still cheap to change.
Custom equipment
Equipment manufactured to the site's real dimensions and capacity, including the non-standard items a catalogue cannot cover.
Standardised construction
One construction standard, one installation sequence and one acceptance regime across every zone.
Integrated commissioning
Systems are commissioned against each other, not in isolation — so the hand-over is a working facility, not a set of finished machines.
Lifecycle operation
The information and control layer that manages the facility after hand-over. Detailed on its own solution page.
Where the five zones meet
Cold storage · Cremation & flue gas · Ash storage · Air safety & purification · Information systems. These are exactly the boundaries that fail in a zone-by-zone procurement — and exactly what a single contract is for.
03 How it works
The delivery method is fixed and does not change with project size. It runs as five stages, supported by nine working steps that begin with a site survey and end with commissioning.
01
Unified planning
Survey the site, capture requirements and agree the functional zones, capacities and constraints.
02
Integrated design
Plan function, space and operation; fix equipment interfaces before construction.
03
Custom equipment
Manufacture equipment to the agreed site dimensions, capacity and control architecture.
04
Standardised construction
Build and install to one standard, with equipment installation overlapped into the programme.
05
Integrated operation
Commission the systems against each other and hand over a facility that runs as one.
Nine working steps behind the five stages
Site survey · Requirement communication · Feedback · Function planning · Space planning · Operation planning · Space build-out · Equipment customisation · System commissioning.
04 Where it applies
The solution is written for new construction, renovation and expansion alike. The functional zones below are the ones covered by every turnkey scope, and they follow the service flow of the facility itself.
Cold storage & mortuaryCremation hallFlue-gas treatmentAsh storageEmbalming & cosmeticsMemorial hallsBusiness & receptionAncillary office & living
01
Intake
Body received and prepared at the side entrance.
02
Preparation
Washing, preservation and cosmetics in the air-safety clean rooms.
03
Memorial
Families gather in the memorial halls and observation areas.
04
Cremation
Cremation with the flue-gas train running alongside.
05
Worship
Memorial and ritual areas served by the incineration equipment.
06
Ash storage
Ash placed in the storage rooms, linked back to the information system.
05 Technical basis
Design and construction follow the Chinese national and industry standards below, together with the equipment standards listed on the individual solution pages.
| Standard | Subject |
|---|---|
| GB 50016-2019 | Fire protection design for buildings |
| GB 50303-2015 | Acceptance of electrical installation |
| GB 50243-2016 | Acceptance of ventilation and air-conditioning works |
| GB 50738-2011 | Code for ventilation and air-conditioning construction |
| GB 50981-2014 | Seismic design of building mechanical and electrical systems |
| GB 50189-2015 | Energy-efficiency design for public buildings |
06 Selected references
Yueyang Funeral HomeHunan Province — full facility
Binzhou Funeral HomeShandong Province — full facility
Lishui Funeral HomeNanjing, Jiangsu Province
Xinpu District Funeral HomeZunyi, Guizhou Province
Shangyao Funeral Service CentreLiyang, Jiangsu Province
Zhangshu Funeral HomeJiangxi Province
Reference projects drawn from the company's delivered portfolio. Additional references outside your region can be provided on request, subject to client consent.
08 Questions buyers ask
Can you take on a renovation rather than a new building?
Yes. The same five stages apply. A renovation begins with a survey of the existing structure and services, and the integrated design stage is where the constraints of the existing building are resolved against the equipment layout.
How many functional zones can one contract cover?
All five: cold storage, cremation and flue gas, ash storage, air safety and purification, and information systems. Partial scopes are possible, but the interface benefit is greatest when the zones that physically touch each other sit under one contract.
What do you need from us to quote?
The site location and size, the functional zones required, the daily capacity you are planning for, the country and the project stage. Send those and we will respond with scope, interfaces and the standards we will build to.
Do you publish prices?
No. A turnkey scope depends on the site, the zones and the capacity, so it is quoted per project after the planning conversation rather than from a list.
Where to go next
Scope this solution for your project.
Send the site, the zones and the stage you are at. We reply with what we would deliver, which interfaces we would own and the standards we would build to.